TerraCycle's WINTR Fairing Kit can keep you riding even when the winds blow cold. WINTR stands for Weather-Inhibiting 'N Travel Ready. When the shelter provided by a time-tested Windwrap fairing combines with the easy to install and easy to transfer mounting hardware from T-Cycle, you have a system meticulously designed to keep you on the road no matter what the weather is doing. Utilizing the power of T-Cycle's exquisite CNC machining, the mounting hardware is stronger and simpler to use than ever before. The WINTR Fairing Kit includes a fairing along with all the mounting hardware needed to mount it to your bike or trike.
$128.00 - $160.00
Looking to electrify your Catrike recumbent trike? This CNC machined battery mount allows you to mount a battery under the seat and close to the centerline of your Catrike, the best place to mount a battery. The mount consists of a heavy duty clamp that attach to the frame, an angle adjustable vertical plate that attaches to the frame clamp, and a battery shelf that attaches to the vertical plate. The battery shelf is large and sturdy, and set up to hold the common batteries, like the BionX, that use standard bottle boss spacing. Additional plates to mount less common batteries like the BionX rear rack battery are also available. For other batteries in shrink wrap or nylon housings, you can usually strap them on or use zip ties. Precision made for Catrike recumbent trikes, this battery mount is the super sturdy, elegant battery solution that you need for your electric trike. On the folding Catrikes, the battery mount has to be on the right in order to work with the fold. Right side configurations include the optional extender to clear the chain. On the Villager, the extender is required for both sides. Recommended maximum battery weight is 15 lbs (6.8Kg).
This TerraCycle made Battery Mount for Suspended ICE Trikes comes with a shelf drilled to allow the mounting of many different batteries. The attaches your electric motor kit battery to your ICE trike down low and out of the way. In fact, it lets you put the battery so out of the way that you can fold the trike with the battery attached! All parts machined from 6061-T6 aluminum and black anodized. All fasteners are stainless steel. Fits all ICE suspended trikes from 2011 onwards. Contact us about battery mounting options for other trikes.
Like all TerraCycle idlers, these will ensure trouble-free miles with less vibration and more power delivered to the drive train. The Catrike Dual Idler Kit is for Catrikes that didn't come with a TerraCycle idler. This kit essentially replaces your stock Catrike parts with high-end TerraCycle idlers. Depending on your boom setup, you can eliminate most if not all of your chain tube! The kit includes a Sport Power Idler, Return Idler, and a Stainless Single Chain Keeper, a Floating Chaintube Holder and all the hardware to make it run beautifully.
This is the Power Idler kit to seriously upgrade your stock sytem. Custom idler mounting brackets house a Terracycle Power Idler in Titanium cog. You won't believe how much smoother and quieter your bike will be until you install this kit and go for your first test ride. Note: On older bikes with the square seat channel, you may need to trim the excess length from the right side seat clamp L bracket. Since TerraCycle idlers are larger for greater efficiency, this raises the chainline and may produce rubbing of the chain on the right side L bracket unless it is shortened. Rad-Loc seat clamp bikes are OK.
This versatile bag could hold a small pump, tools, spare tube, phone, wallet, and snack bar, and is designed to fit on tubes up to 70mm or so, including the main tubes on Bacchetta’s Carbon Aero. Made from waterproof materials and a waterproof zipper, the Fastback NorBack frame pack will keep your stuff dry in all but the very wettest conditions, and is built to last. Details: 14 inches (35mm) long, 5 inches (13cm) tall. There is one main pocket with a wide Velcro loop on the ceiling that is designed to hold a mini pump. There are two zipper pockets on the inside front. The top is reinforced with a removable stiffener to keep it in position on your bike. Compatible with nearly any bike or trike.
$59.00 - $69.00
This is a low profile CLAMP that attaches to your handlebars and an accessory mounting tube. The clamp can go almost anywhere- all it needs is 1/2 inch (12mm) of straight handlebar. The accessory mounting TUBE is available separately. The outside clamp is designed to clamp around a painted or anodized 7/8 inch (22.2mm) tube. Only 1/2 inch (12.7mm) of open handlebar space is required. The inside clamp is designed to clamp to the inside of a 7/8 inch tube with a wall thickness of 0.065 to 0.049 inches (1.6 to 1.24mm). Most 7/8 tubing for bikes and trikes is in this range. This clamp is designed to be small and lightweight. It is not designed for heavy loads or to carry steering forces.
Ever wanted to attach a computer, GPS, motor controller, or phone right near your hands on your recumbent trike? Ever wanted to attach something like a mirror to the ends your handlebars, but you have Bar End Shifters? This accessory mount is the one. This mount uses a special clamp with a Cable Tunnel in it that attaches to the end of your handlebars right under your Bar End Shifters. The clamp goes forward and inward a little bit and holds mounting tube that goes up and then out. Since the clamp goes inward a little bit, your hands slide right past it. You'll barely notice it's there as you go from braking to shifting and back. What you will notice is that your mirror is now right where you want it to be, and that you can easily see your phone and operate the buttons on your motor controller. Left or right hand installation. This mount is not for assistance in getting in and out of your trike.
This pack can attach to the back of a recumbent seat if there is a horizontal bar available, as in the Sunseeker bikes and trikes and many Catrike models. A roomy pack measuring 8 inches tall, 11.5 wide, and 4 inches thick, you can carry your essentials and a little more, but is not designed for heavy cargo.
$24.00 - $28.00
An essential building block in the Cockpit Mount family is the Double-Ended Cockpit Mount Clamp. The 7/8" to 7/8" clamp allows you to clamp to two 7/8" tubes, while the 1" to 7/8" clamp attaches to two tubes of different sizes. The open-ended, two-screw setup means that installation is a breeze, because you don't have to remove other things from your tube. The high surface area of the Double-Ended Cockpit Mount Clamp's grip securely clamps into place, holding any accessories or mounts wherever you want them to be. Not meant for use with steering controls. Use it with a cockpit elbow mount to install lights, computers, phone holders, and more on your recumbent bike or trike.
An elbow mount coupled with a double-ended cockpit clamp lets you install accessories on your recumbent bike or trike. The 90° Cockpit Mount Elbow Tube functions to change the direction of your mount from horizontal to vertical (or vice versa). The 7/8" width is an industry standard size, which makes for easy connecting or mounting. The compact length is long enough connect two clamps comfortably while still stylishly blending into the mounting system.
These accessory mounts fit on the fixed side of the bar end shifter, and allow you to mount small accessories such as a cycle computer, thumb throttle, or motor controller button. Fits any bike or trike with Shimano, Microshift, or SRAM Bar End Shifters. Can be combined with the TerraCycle Handlebar Accessory Mount Clamps, which fit inside the long length Bar End Shifter Micro Mount. Short versions are 15mm (0.6in) long. Long versions are 30mm (1.2in) long. Both are 22.2mm (7/8in) outside diameter (the standard handlebar size). All are CNC machined 6061T6 aluminum, black anodized. The inside is hollowed out to 18.9mm (0.74in).
These clamps are modified Cateye brand clamps. Cateye clamps are the best plastic band clamps made. Terracycle made them even more useful by pressing in an anodized aluminum spacer and replacing the attachment screw with a stainless steel bolt. Sold in pairs.
This extender kit gives you 15mm of additional space to mount another accessory. Some folks want to run a small blinking white light alongside their main illumination light. In the rear facing configuration, this extender allows you to mount two accessories to the mount ie: computer and GPS, or computer and separate heart rate monitor. The possiblities are endless. The kit is composed of a 15mm add on mount, a fitted end cap, and a new longer stainless bolt. This kit allows you to add space to either or both sides of your existing accessory mount.
Here's another help for attaching computers, lights and other goodies to your recumbent bike or trike. The 40mm Straight Link Tube can function as either an articulating joint or a mini mount all by itself. The 7/8" is an industry standard size, which makes for easy connecting or mounting. The compact 40mm length is long enough to hold a small mount and short enough that, when acting as an articulating joint, it stylishly blends into the mounting system. Specifications: 40mm long; made from 6061-T6 aluminum; powder coated black; Weight: 14 grams
Page 1 of 1